Afișez toate cele 17 rezultate

  • Driver Motoare pas cu pas 2DM860H (Noua generatie 2M982)

    Driver Motoare pas cu pas 2DM860H (Noua generatie 2M982)

    Caracteristici * Noua tehnologie DSP pe 32 de biți * Intrări diferențiale izolate optic (26LS32) * Zgomot și vibrații extrem de scăzute * compatibil cu motoare pas cu pas în două faze cu 4,6,8 fire * Setările curente pot fi alese în mod arbitrar * Curentul staționar este înjumătățit automat * Frecvența frecvenței pulsului până la 250KHz * Supratensiune, subtensiune, protecție la scurtcircuit * Funcții de ieșire alarmă I / O porturi * Intrare clară de alarmă ENA Introducere 2DM860 este cel mai nou driver digital de pas cu pas lansat de JMC, folosind cea mai recentă tehnologie de control DSP pe 32 de biți, utilizatorul poate seta orice segment în limitele 25600 și valoarea curentă multiplă în curent nominal, cu micro-tehnologie încorporată. Stabilitate și zgomot redus în subdiviziune (microstepping). Integrarea funcției de reglare automată a parametrilor în interior permite, de asemenea, reglarea automată a parametrilor optimi de funcționare pentru motoare diferite pentru a maximiza performanța motorului. Specificații Parametrii Min Typical Max Unit Curent de ieșire (vârf la vârf) 2.1 – 8.4 Amperi Tensiunea de alimentare 30VAC (DC40V) 60VAC (DC80V) 80VAC(DC110V) VAC Logic Input Current – 10 – mA Frecvența impulsurilor de intrare – – 250 KHz Low Level Time 2.5 – – µsec Cooling Natural Cooling or Forced Convection Environment Space Avoid dust, oil frost and corrosive gases Ambient Temperature 0°C-65°C Humidity <80%RH Vibration 5.9m/s² Max Storage Temp. -10°C -80°C Weight Approx. 0.58Kg Dimensions (mm) Current Setting: Current Setting AVG(A) Peak Value(A) SW1 SW2 SW3 1.5 2.1 OFF OFF OFF 2.25 3.15 ON OFF OFF 2.88 4.03 OFF ON OFF 3.42 4.78 ON OFF ON 4.06 5.69 OFF OFF ON 4.60 6.44 ON OFF ON 5.25 7.35 OFF ON ON 6.0 8.4 ON ON ON Microstep Setting: Step/Rev SW5 SW6 SW7 SW8 400 ON ON ON ON 800 OFF ON ON ON 1600 ON OFF ON ON 3200 OFF OFF ON ON 6400 ON ON OFF ON 12800 OFF ON OFF ON 25600 ON ON ON OFF 51200 OFF OFF OFF ON 1000 ON ON ON OFF 2000 OFF ON ON OFF 4000 ON OFF ON OFF 5000 OFF OFF ON OFF 8000 ON ON OFF OFF 10000 OFF ON OFF OFF 20000 ON OFF OFF OFF 40000 OFF OFF OFF OFF * SW4: ON=Full current, SW4 : OFF=Half current Funcția de jumătate de curent înseamnă că nu există un impuls 200ms, Ieșirile curentului de iesire a driverului reduse automat la 50% din curentul nominal de ieșire, pentru a preveni încălzirea motorului. P1 Pin Assignment Signal Function Descriptions PLS+ Input signal positive end Connected to + 5V power supply, + 5V ~ + 24V can be driven, above 5V need current limiting resistor. PLS- Pulse signal Falling edge, pulse from high to low whenever the motor step. Input resistance 220Ω, requirements; low 0-0.5V, high 4-5V, pulse width <2.5uS. DIR+ Input signal positive end Connected to + 5V power supply, + 5V ~ + 24V can be driven, above 5V need current limiting resistor. DIR- Direction control signal Used to change the direction, input resistance 220Ω, requirements; low 0-0.5V, high 4-5V, pulse width <2.5uS. ENA+ Input signal positive end Connected to + 5V power supply, + 5V ~ + 24V can be driven, above 5V need current limiting resistor. ENA- Motor release signal Off active (low) when power motor current, the drive stops working, the motor is in a free state. ALM+ Alarm output positive Open collector output ALM- Alarm output negative Open collector output P2 Pin Assignment The P2 I/o high voltage interface description AC2 Name Function Instructions A+、A- B+、B- Electrical wiring AC1 AC2 voltage input Between AC30~80V,refer to motor specs Wiring Signal waveform and timing

    Caracteristici * Noua tehnologie DSP pe 32 de biți * Intrări diferențiale izolate optic (26LS32) * Zgomot și vibrații extrem de scăzute * compatibil cu motoare pas cu pas în…
  • UC400ETH ethernet motion controller

    UC400ETH ethernet motion controller

    Features: – Replaces 2 pieces of standard LPT ports. – Controls upto 6-axis simulteneously. – Works with the UCCNC software and Mach3. – Upto 400kHz step frequency operation. – Ethernet connection to the control PC. – Same pinout as a standard LPT port. – Fast communication with data buffer for robust and stabile operation. Downloads for this product: 1.) Product manual 2.) UCx00 automatic installer for Mach3 3.) Plugin for manual installation 4.) UCxx Utility software 5.) Rigid tapping macro for Mach3 6.) Software prerequirements

    Features: - Replaces 2 pieces of standard LPT ports. - Controls upto 6-axis simulteneously. - Works with the UCCNC software and Mach3. - Upto 400kHz step frequency operation. - Ethernet…
  • AXBB-E ethernet motion controller and breakout board combined controller

    AXBB-E ethernet motion controller and breakout board combined controller

    Features: – Complete motion controller and breakout board solution in a single board. – 8 optically isolated high speed N-channel power mosfet transistor outputs.(NPN) – 9 non-isolated buffered TTL outputs to control step/dir signals, laser driver etc. – Isolated charge pump output with power N-channel mosfet transistor. – 6 high speed optoisolator inputs. – 1 IDC26 non-isolated extension port with standard LPT port pinout (12 outputs and 5 inputs). – LED indicators on isolated I/Os. – Isolated I/Os are 24Volts capable. Downloads for this product: . 1.) Product manual . 2.) UCx00 automatic installer application for Mach3 The following drawing shows an example connection setup of the AXBB-E controller:

    Features: - Complete motion controller and breakout board solution in a single board. - 8 optically isolated high speed N-channel power mosfet transistor outputs.(NPN) - 9 non-isolated buffered TTL outputs…
  • Advanced Microstepping Driver M542 2M542

    Advanced Microstepping Driver M542 2M542

    Microstepping la urmatoarele nivele : 2,4,8,16,32,64,128. Sau : 5,10,20,25,40,50,100,125 microstep/pas nativ al motorului. Curentul maxim prin bobine poate fi reglat in 8 trepte pana la curentul maxim admis. Microstep Steps/rev. (1.8°motor) SW5 SW6 SW7 SW8 2 400 OFF ON ON ON 4 800 ON OFF ON ON 8 1600 OFF OFF ON ON 16 3200 ON ON OFF ON 32 6400 OFF ON OFF ON 64 12800 ON OFF OFF ON 128 25600 OFF OFF OFF ON 5 1000 ON ON ON OFF 10 2000 OFF ON ON OFF 20 4000 ON OFF ON OFF 25 5000 OFF OFF ON OFF 40 8000 ON ON OFF OFF 50 10000 OFF ON OFF OFF 100 20000 ON OFF OFF OFF 125 25000 OFF OFF OFF OFF Setarea de curent Peak current (A) RMS (A) SW1 SW2 SW3 1 0.71 ON ON ON 1.46 1.04 OFF ON ON 1.91 1.36 ON OFF ON 2.37 1.69 OFF OFF ON 2.84 2.03 ON ON OFF 3.31 2.36 OFF ON OFF 3.76 2.69 ON OFF OFF 4.2 3 OFF OFF OFF CNC Control Software (Machining/Milling/Lathe): EMC – Linux AXIS – GUI for EMC2 KCAM – Windows 98 TurboCNC – DOS Mach2/3 – Windows 2000/XP DeskCNC – Windows CNCZeus – DOS Master5 – Windows 95/98 DesKAM – Windows/DOS CNCPro – DOS (recently opened sourced) USBCNC – USB controlled CNC CNCDudez – Another USB controlled CNC

    Microstepping la urmatoarele nivele : 2,4,8,16,32,64,128. Sau : 5,10,20,25,40,50,100,125 microstep/pas nativ al motorului. Curentul maxim prin bobine poate fi reglat in 8 trepte pana la curentul maxim admis. Microstep Steps/rev.…
  • DG4S-16035 servo drive

    DG4S-16035 servo drive

    DG4S-16035 servo drive Download the product manual Download the configuration software Features: – Power: 160V and 35A. – Opto-isolated step/direction inputs. – Tuning through optically isolated USB port. – RJ45 connectors for PLUG&PLAY like easy connection. – Selectable 2x and 4x encoder logic. – Step signal multiplier with selectable 1x, 2x, 3x, 4x, 5x, 6x, 7x, 8x, 9x, 10x options. – Setable servo error limit from 2 to 20000 encoder counts. – Fast 32bit advanced PID algorithm with 16bit PID – parameters and setable sampling time. – 2 stage Current limiting, adjustable from 0 to 35Ampers. – Servo error viewer software and diagnostics. – 32bit DRO built into Servoconfigurator3 software. – Step response analyser in software.

    DG4S-16035 servo drive Download the product manual Download the configuration software Features: - Power: 160V and 35A. - Opto-isolated step/direction inputs. - Tuning through optically isolated USB port. - RJ45…
  • UCR200 Wireless jog pendant

    UCR200 Wireless jog pendant

    Features: – Wireless (WIFI) jog pendant to use with Mach3 – 10-15meters transmit range (depends on environment) – 4-axis on screen. (upto 6-axis selectable). – Works with Mach3 software via plugin. – LCD screen with backlight – USB wifi transmitter connects to the control PC. – Handwheel encoder and pushbuttons. – Battery operation with long life. (batteries replaceble) Mach3 downloads for this product: 1.) Product manual 2.) UCx00 automatic installer application 3.) Mach3 UCR200 plugin Downloads for OEMs, for Visual Studio development: 1.) Example project to use the pendant from own software written in VB .net. This download contains an example VB software and a header file as documentation..

    Features: - Wireless (WIFI) jog pendant to use with Mach3 - 10-15meters transmit range (depends on environment) - 4-axis on screen. (upto 6-axis selectable). - Works with Mach3 software via…
  • Motion controller UC100-USB

    Motion controller UC100-USB

    – Inlocuieste portul Parallel. – Poate sa comande pana la 6-axe simultan. – Functioneaza cu Mach3 printr-ul plugin. – Viteza maxima pana la 100kHz operation. – USB . – Acelas pinout ca si un LPT port. – Comunicare rapdida cu data buffer pentru o functionare robusta si stabila Poate functiona cu Mach3 sau cu UCCNC

    - Inlocuieste portul Parallel. - Poate sa comande pana la 6-axe simultan. - Functioneaza cu Mach3 printr-ul plugin. - Viteza maxima pana la 100kHz operation. - USB . - Acelas…
  • HDBB2 breakout board

    HDBB2 breakout board

    Features: – Centronix-36 connector for standard LPT cable connection. – IDC-26 connector for DSUB-25 ribbon connection. – 4 x Open-drain Mosfet outputs for external relay control.. – 4 x RJ45 servo or stepper axis connections. – All 5 inputs optically isolated. – 1 analog output for VFD control. – Built in charge pump safety function. – LEDs on all in and outputs for easy visual debugging.. https://www.cncdrive.com/HDBB2.html

    Features: - Centronix-36 connector for standard LPT cable connection. - IDC-26 connector for DSUB-25 ribbon connection. - 4 x Open-drain Mosfet outputs for external relay control.. - 4 x RJ45…
  • 4A 4 Axis Bipolar Microstep Driver CNC4X45A

    4A 4 Axis Bipolar Microstep Driver CNC4X45A

    Specificatiile controllerului de motoare CNC4X45A : Proiectat pentru constructia/retehnologizarea facila a unei masini de frezat sau gravat. Comanda 4 motoare in mod bipolar microstepping Permite conectarea unei game largi de motoare (5-35V si 0,5-4,2A) Permite conectare a 5 semnale de intrare (folosite de obicei la E-Stop, Probe si limitele de cursa pe X Y Z) un releu pe placa pentru pentru comanda pornit oprit a masinii de frezare – gaurire Indicator cu led pentru alimentare, semnalele de intrare si starea driverelor motoarelor Toate iesirile dinspre computer spre placa de comanda sunt procesate de un bufer si triger schmidt Firmware-ul microcontrollerului este open source Configurare timer pentru reducerea curentului prin bobinele motoarelor dupa o perioada de inactivitate Driverul 4 poate fi configurat din dip switch-uri sa faca “shadow”/urmareasca axa X , Y , Z sau sa lucreze ca axa A Compatibila cu un numar mare de programe (De ex : Mach2/3, Master5, EMC,KCAM, USBCNC, WinPC – NC etc.) Fiecare din cele 4 canale de comanda motor prezinta urmatoarele functionalitati : Control PWM cu punte HBridge DMos duala Reglaj de curent in valorile 0.5 – 4.1 continuu cu semireglabil Selectie mod de mocrostepping la 1/1, 1/2 mod A (0% – 71% – 100%), 1/2 mod B (0% – 100%), 1/4, 1/8, 1/16 cu un dipswitch Configurare individuala pentru reducerea curentului prin bobine dupa o perioada de inactivitate Mod automat si configurabil de procesare a curentului indus de bobine (Slow+Fast Decay) Rectificare sincrona a curentului indus pentru o disipare de energie redusa Protectie la supra incalzire Driverele de motoare bipolare sunt cele mai folosite (daca nu singurele) aplicatiile industriale. Chiar daca sunt solutii mai scumpe ele ofera performante si eficienta ridicata. Driverele bipolare folosesc un set suplimentar de tranzistori de comutatie pentru a elimina necesitatea folosirii a doua surse de tensiune. In plus acestea folosesc o punte de 4 tranzistori si diode de recirculare pentru fiecare infasurare a motorului si o rezistenta de valoare redusa prin care se evaluaza curentul in bobina si este mentinuta constanta energia in bobina constanta in toate modurile de microstepping. Driverul vine insotit de : – instructiuni de folosire – cablu paralel cu 25 de pini – radiatoare montate pe placa (ventilatorul nu este inclus in pret) La achizitionarea acestui produs primiti gratuit un set de 4 conectori ! http://magazin.dioda.ro/ro/accesorii-cnc/68-set-de-4-conectori-cu-4-pini.html Va recomandam sa parcugeti urmatorul articol ce va va ajuta in alegerea motorului si driverului potrivit pentru aplicatia dumneavoastra : Top 10 Mituri si Sfaturi despre driverele si motoarele pas cu pas Consideratii referitoare la alegerea unui tandem motor + driver de motoare pas cu pas http://www.dioda.ro/News/article/sid=23.html IAta mai jos o lista de controllere CNC : EMC – Linux AXIS – GUI for EMC2 KCAM – Windows 98 TurboCNC – DOS Mach2/3 – Windows 2000/XP DeskCNC – Windows CNCZeus – DOS Master5 – Windows 95/98 DesKAM – Windows/DOS CNCPro – DOS (recently opened sourced) USBCNC – USB controlled CNC CNCDudez – Another USB controlled CNC http://www.planet-cnc.com/ – CNC USB PIC 4550

    Specificatiile controllerului de motoare CNC4X45A : Proiectat pentru constructia/retehnologizarea facila a unei masini de frezat sau gravat. Comanda 4 motoare in mod bipolar microstepping Permite conectarea unei game largi de…
  • Driver Profesional 50V 4.2A M542

    Driver Profesional 50V 4.2A M542

    Driverul IM542 este o solutie eficienta si economica, de inalta performanga pentru comanda motoarelor pas cu pas bi-polarein mod micro-stepping, generand un curent de control de tip pur-sinusoidal. Este foarte potrivit pentru aplicatii unde este necesar un zgomot foarte redus si incalzire minima. Functioneaza foarte bine si in medii unde sursa de alimentare nu este constanta sau are riplu. Driverul are functionalitatea de optimizare si control automat al vitezei, iesirea este foarte stabila cu vibratie si zgomot aproape 0. In aplicatii functionarea este aproape de un sistem servo. Specifications Parameters Min Typical Max Unit Output Current(Peak) 1.0 – 4.2 Amps Supply voltage 20 36 50 VDC Logic Input Current 7 10 16 mA Pulse input frequency 0 – 200 KHz Low Level Time 2.5 µsec Cooling Natural Cooling or Forced Convection Environment Space Avoid dust,oil forced frost and corrosive gases Ambient Temperature 0℃—50℃ Humidity 40—80%RH Vibration 5.9m/s² Max Storage Temp -10℃—80℃ Weight Approx 260gram Current Setting Current Setting(A) SW1 SW2 SW3 1.0 ON ON ON 1.46 OFF ON ON 1.91 ON OFF ON 2.37 OFF OFF ON 2.84 ON ON OFF 3.31 OFF ON OFF 3.76 ON OFF OFF 4.20 OFF OFF OFF Wiring Dimensions in mm

    Driverul IM542 este o solutie eficienta si economica, de inalta performanga pentru comanda motoarelor pas cu pas bi-polarein mod micro-stepping, generand un curent de control de tip pur-sinusoidal. Este foarte…
  • UC300ETH-5LPT ethernet motion controller

    UC300ETH-5LPT ethernet motion controller

    Features: – Controls upto 6-axis simultaneously. – Works with the UCCNC software and Mach3. – Upto 400kHz step frequency operation. – 49 digital inputs and 36 digital outputs in 5 IDC26 ports. – LPT port compatible. – 2 analog inputs and 2 analog outputs. – Ethernet connection to the control PC. – Works with direct connection to the PC and via routers/switches. – Fast communication with data buffer for robust and stabile operation. . Downloads for this product: . 1.) Product manual 2.) UCx00 automatic installer for Mach3 3.) Plugin for manual installation 4.) UCxx Utility software 5.) Rigid tapping macro for Mach3 6.) Software prerequirements

    Features: - Controls upto 6-axis simultaneously. - Works with the UCCNC software and Mach3. - Upto 400kHz step frequency operation. - 49 digital inputs and 36 digital outputs in 5…
  • CNCUSB + CNC4X35A-B CNCUSB-CNC4X35A-B

    CNCUSB + CNC4X35A-B CNCUSB-CNC4X35A-B

    Un pachet format din cele 2 produse la un pret foarte avantajos.

    Un pachet format din cele 2 produse la un pret foarte avantajos.
  • Driver motor pas cu pas 7,9A 80v 2M982

    Driver motor pas cu pas 7,9A 80v 2M982

    Caracteristici principale: Tensiunea de alimentare 24 – 80VDC Pentru motoarele bipolare cu 4, 6 si 8 fire de legatura, Curent de iesire selectabil in domeniul 1.8 ~ 7.9A Reducerea curentului cu 50% automat atunci cand motorul nu se afla in miscare Frecventa maxima a semnalului de step de intrare este de 200 kHz Intrari izolate galvanic pentru semnalele de intrare Pulse, Direction si Enable Microstepping selectabil pana la 1/128 din pasul nativ al motorului Protectie la supratensiune, scurtcircuit intre bobine sau scurtcircuit bobina catre masa PRodusul poate fi prezentat cu codul PSD8079 sau 2M982.

    Caracteristici principale: Tensiunea de alimentare 24 - 80VDC Pentru motoarele bipolare cu 4, 6 si 8 fire de legatura, Curent de iesire selectabil in domeniul 1.8 ~ 7.9A Reducerea curentului…
  • CNC USB Motion Controller CNCUSB1

    CNC USB Motion Controller CNCUSB1

    CNC USB Motion Controller realizeaza conexiunea intre un computer personal si driverele de motoare pas cu pas. Acesta foloseste un port USB care este disponibil la computerele actuale si la laptop-uri. Comanda 4 axe. Este solutia HardWare pentru programul de comanda de la adresa : http://www.planet-cnc.com Poate fi alimentat din sursa externa de tensiune : 10-30V din portul USB sau de la placa driver de motoare CNC4X35AP Atentie include doar kit-ul electronic de conversie din port USB catre parallel si nu si licenta de functionare a programului de comanda. Programul de comanda se downloadeaza de la adresa : http://www.planet-cnc.com sectiunea download. Link-ul direct este : http://www.planet-cnc.com/files/Setup20-20110830.zip Functionalitati si Specificatii ale solutiei : Conexiune USB (V2.x) de la un PC/Laptop care ruleaza Windows XP, Vista sau Windows 7 (32 bit sau 64bit) Controllerul functioneaza cu majoritatea driverelor step/dir disponibile Algoritmi de interpolare avansate Start, stop, pause si resume program execution Poate importa cod standard RS274/NGC G-code (EMC2 compatibil) Interpreteaza si executa G-code-uri avansate – G40, G41, G42 (Cutter Radius Compensation) Interpreteaza si executa G-code-uri avansate – G43, G49 (Tool Length Offsets) supported Interpreteaza si executa G-code-uri avansate – G54, G59.3 (Coordinate System Origins) Solutie tesata cu cod G-code generat din SolidCAM, MasterCAM, ArtCAM, Vectric, … Suporta cod Profili 4-axe si 3-axe Import toolpath din fisiere DXF files Importa toolpath din fisiere PLT/HPGL Import toolpath din fisiere imagine Importa /genereaza toolpath din fisiere NC-Drill (Excellon) Importa toolpath din fisiere Gerber (RS-274X) SImuleaza Tollpath-ul Procedura automata de homing Procedura automata de toolchange Exporta toolpath in G-code Exporta toolpath-ul in DXF Functioneaza si pe MacOS X (Snow Leopard 10.6.3) pe o masina virtuala care emuleaza Windows XP SP3 ?

    CNC USB Motion Controller realizeaza conexiunea intre un computer personal si driverele de motoare pas cu pas. Acesta foloseste un port USB care este disponibil la computerele actuale si la…
  • UCSB single port breakout board + 1xIDC26-IDC26_250mm

    UCSB single port breakout board + 1xIDC26-IDC26_250mm

    UCSB single port breakout board + 1xIDC26-IDC26_250mm Features: – IDC26 port with standard LPT port pinout. – 12 outputs and 5 inputs. – All I/Os optical isolated with high speed 10Mbit/sec optocouplers. – Open-drain Mosfet outputs for external relay control. – Pluggable screw terminals. – LED indicators on all I/Os. – 24V capable I/Os.

    UCSB single port breakout board + 1xIDC26-IDC26_250mm Features: - IDC26 port with standard LPT port pinout. - 12 outputs and 5 inputs. - All I/Os optical isolated with high speed…
  • DG4S-08020 servo drive

    DG4S-08020 servo drive

    Features: – Power: 80V and 20A. – Opto-isolated step/direction inputs. – Tuning through optically isolated USB port. – RJ45 connectors for PLUG&PLAY like easy connection. – Selectable 2x and 4x encoder logic. – Step signal multiplier with selectable 1x, 2x, 3x, 4x, 5x, 6x, 7x, 8x, 9x, 10x options. – Setable servo error limit from 2 to 20000 encoder counts. – Fast 32bit advanced PID algorithm with 16bit PID – parameters and setable sampling time. – 2 stage Current limiting, adjustable from 0 to 20Ampers. – Servo error viewer software and diagnostics. – 32bit DRO built into Servoconfigurator3 software. – Step response analyser in software.

    Features: - Power: 80V and 20A. - Opto-isolated step/direction inputs. - Tuning through optically isolated USB port. - RJ45 connectors for PLUG&PLAY like easy connection. - Selectable 2x and 4x…
  • UCBB dual port breakout board + 2xIDC26-IDC26_250mm

    UCBB dual port breakout board + 2xIDC26-IDC26_250mm

    UCBB dual port breakout board + 2xIDC26-IDC26_250mm Features: – 2x IDC26 ports with LPT port pinout. One standard LPT port and one input type LPT port. – 16 outputs and 18 inputs. – All I/Os optical isolated with high speed 10Mbit/sec optocouplers. – Open-drain Mosfet outputs for external relay control. – Pluggable screw terminals. – LED indicators on all I/Os. – 24V capable I/Os.

    UCBB dual port breakout board + 2xIDC26-IDC26_250mm Features: - 2x IDC26 ports with LPT port pinout. One standard LPT port and one input type LPT port. - 16 outputs and…